# scipy.sparse.linalg.lsmr¶

scipy.sparse.linalg.lsmr(A, b, damp=0.0, atol=1e-06, btol=1e-06, conlim=100000000.0, maxiter=None, show=False)[source]

Iterative solver for least-squares problems.

lsmr solves the system of linear equations Ax = b. If the system is inconsistent, it solves the least-squares problem min ||b - Ax||_2. A is a rectangular matrix of dimension m-by-n, where all cases are allowed: m = n, m > n, or m < n. B is a vector of length m. The matrix A may be dense or sparse (usually sparse).

Parameters: A : {matrix, sparse matrix, ndarray, LinearOperator} Matrix A in the linear system. b : (m,) ndarray Vector b in the linear system. damp : float Damping factor for regularized least-squares. lsmr solves the regularized least-squares problem: min ||(b) - ( A )x|| ||(0) (damp*I) ||_2  where damp is a scalar. If damp is None or 0, the system is solved without regularization. atol, btol : float, optional Stopping tolerances. lsmr continues iterations until a certain backward error estimate is smaller than some quantity depending on atol and btol. Let r = b - Ax be the residual vector for the current approximate solution x. If Ax = b seems to be consistent, lsmr terminates when norm(r) <= atol * norm(A) * norm(x) + btol * norm(b). Otherwise, lsmr terminates when norm(A^{T} r) <= atol * norm(A) * norm(r). If both tolerances are 1.0e-6 (say), the final norm(r) should be accurate to about 6 digits. (The final x will usually have fewer correct digits, depending on cond(A) and the size of LAMBDA.) If atol or btol is None, a default value of 1.0e-6 will be used. Ideally, they should be estimates of the relative error in the entries of A and B respectively. For example, if the entries of A have 7 correct digits, set atol = 1e-7. This prevents the algorithm from doing unnecessary work beyond the uncertainty of the input data. conlim : float, optional lsmr terminates if an estimate of cond(A) exceeds conlim. For compatible systems Ax = b, conlim could be as large as 1.0e+12 (say). For least-squares problems, conlim should be less than 1.0e+8. If conlim is None, the default value is 1e+8. Maximum precision can be obtained by setting atol = btol = conlim = 0, but the number of iterations may then be excessive. maxiter : int, optional lsmr terminates if the number of iterations reaches maxiter. The default is maxiter = min(m, n). For ill-conditioned systems, a larger value of maxiter may be needed. show : bool, optional Print iterations logs if show=True. x : ndarray of float Least-square solution returned. istop : int istop gives the reason for stopping: istop = 0 means x=0 is a solution. = 1 means x is an approximate solution to A*x = B, according to atol and btol. = 2 means x approximately solves the least-squares problem according to atol. = 3 means COND(A) seems to be greater than CONLIM. = 4 is the same as 1 with atol = btol = eps (machine precision) = 5 is the same as 2 with atol = eps. = 6 is the same as 3 with CONLIM = 1/eps. = 7 means ITN reached maxiter before the other stopping conditions were satisfied.  itn : int Number of iterations used. normr : float norm(b-Ax) normar : float norm(A^T (b - Ax)) norma : float norm(A) conda : float Condition number of A. normx : float norm(x)

Notes

New in version 0.11.0.

References

 [R26] D. C.-L. Fong and M. A. Saunders, “LSMR: An iterative algorithm for sparse least-squares problems”, SIAM J. Sci. Comput., vol. 33, pp. 2950-2971, 2011. http://arxiv.org/abs/1006.0758
 [R27] LSMR Software, http://web.stanford.edu/group/SOL/software/lsmr/

#### Previous topic

scipy.sparse.linalg.lsqr

#### Next topic

scipy.sparse.linalg.eigs