scipy.signal.ShortTimeFFT.

spectrogram#

ShortTimeFFT.spectrogram(x, y=None, detr=None, *, p0=None, p1=None, k_offset=0, padding='zeros', axis=-1)[source]#

Calculate spectrogram or cross-spectrogram.

The spectrogram is the absolute square of the STFT, i.e, it is abs(S[q,p])**2 for given S[q,p] and thus is always non-negative. For two STFTs Sx[q,p], Sy[q,p], the cross-spectrogram is defined as Sx[q,p] * np.conj(Sx[q,p]) and is complex-valued. This is a convenience function for calling stft / stft_detrend, hence all parameters are discussed there. If y is not None it needs to have the same shape as x.

See also

stft

Perform the short-time Fourier transform.

stft_detrend

STFT with a trend subtracted from each segment.

scipy.signal.ShortTimeFFT

Class this method belongs to.

Examples

The following example shows the spectrogram of a square wave with varying frequency \(f_i(t)\) (marked by a green dashed line in the plot) sampled with 20 Hz:

>>> import matplotlib.pyplot as plt
>>> import numpy as np
>>> from scipy.signal import square, ShortTimeFFT
>>> from scipy.signal.windows import gaussian
...
>>> T_x, N = 1 / 20, 1000  # 20 Hz sampling rate for 50 s signal
>>> t_x = np.arange(N) * T_x  # time indexes for signal
>>> f_i = 5e-3*(t_x - t_x[N // 3])**2 + 1  # varying frequency
>>> x = square(2*np.pi*np.cumsum(f_i)*T_x)  # the signal

The utitlized Gaussian window is 50 samples or 2.5 s long. The parameter mfft=800 (oversampling factor 16) and the hop interval of 2 in ShortTimeFFT was chosen to produce a sufficient number of points:

>>> g_std = 12  # standard deviation for Gaussian window in samples
>>> win = gaussian(50, std=g_std, sym=True)  # symmetric Gaussian wind.
>>> SFT = ShortTimeFFT(win, hop=2, fs=1/T_x, mfft=800, scale_to='psd')
>>> Sx2 = SFT.spectrogram(x)  # calculate absolute square of STFT

The plot’s colormap is logarithmically scaled as the power spectral density is in dB. The time extent of the signal x is marked by vertical dashed lines and the shaded areas mark the presence of border effects:

>>> fig1, ax1 = plt.subplots(figsize=(6., 4.))  # enlarge plot a bit
>>> t_lo, t_hi = SFT.extent(N)[:2]  # time range of plot
>>> ax1.set_title(rf"Spectrogram ({SFT.m_num*SFT.T:g}$\,s$ Gaussian " +
...               rf"window, $\sigma_t={g_std*SFT.T:g}\,$s)")
>>> ax1.set(xlabel=f"Time $t$ in seconds ({SFT.p_num(N)} slices, " +
...                rf"$\Delta t = {SFT.delta_t:g}\,$s)",
...         ylabel=f"Freq. $f$ in Hz ({SFT.f_pts} bins, " +
...                rf"$\Delta f = {SFT.delta_f:g}\,$Hz)",
...         xlim=(t_lo, t_hi))
>>> Sx_dB = 10 * np.log10(np.fmax(Sx2, 1e-4))  # limit range to -40 dB
>>> im1 = ax1.imshow(Sx_dB, origin='lower', aspect='auto',
...                  extent=SFT.extent(N), cmap='magma')
>>> ax1.plot(t_x, f_i, 'g--', alpha=.5, label='$f_i(t)$')
>>> fig1.colorbar(im1, label='Power Spectral Density ' +
...                          r"$20\,\log_{10}|S_x(t, f)|$ in dB")
...
>>> # Shade areas where window slices stick out to the side:
>>> for t0_, t1_ in [(t_lo, SFT.lower_border_end[0] * SFT.T),
...                  (SFT.upper_border_begin(N)[0] * SFT.T, t_hi)]:
...     ax1.axvspan(t0_, t1_, color='w', linewidth=0, alpha=.3)
>>> for t_ in [0, N * SFT.T]:  # mark signal borders with vertical line
...     ax1.axvline(t_, color='c', linestyle='--', alpha=0.5)
>>> ax1.legend()
>>> fig1.tight_layout()
>>> plt.show()
../../_images/scipy-signal-ShortTimeFFT-spectrogram-1_00_00.png

The logarithmic scaling reveals the odd harmonics of the square wave, which are reflected at the Nyquist frequency of 10 Hz. This aliasing is also the main source of the noise artifacts in the plot.