The signal processing toolbox currently contains some filtering functions, a limited set of filter design tools, and a few B-spline interpolation algorithms for one- and two-dimensional data. While the B-spline algorithms could technically be placed under the interpolation category, they are included here because they only work with equally-spaced data and make heavy use of filter-theory and transfer-function formalism to provide a fast B-spline transform. To understand this section you will need to understand that a signal in SciPy is an array of real or complex numbers.

A B-spline is an approximation of a continuous function over a finite- domain in terms of B-spline coefficients and knot points. If the knot- points are equally spaced with spacing , then the B-spline approximation to a 1-dimensional function is the finite-basis expansion.

In two dimensions with knot-spacing and , the function representation is

In these expressions, is the space-limited B-spline basis function of order, . The requirement of equally-spaced knot-points and equally-spaced data points, allows the development of fast (inverse-filtering) algorithms for determining the coefficients, , from sample-values, . Unlike the general spline interpolation algorithms, these algorithms can quickly find the spline coefficients for large images.

The advantage of representing a set of samples via B-spline basis functions is that continuous-domain operators (derivatives, re- sampling, integral, etc.) which assume that the data samples are drawn from an underlying continuous function can be computed with relative ease from the spline coefficients. For example, the second-derivative of a spline is

Using the property of B-splines that

it can be seen that

If , then at the sample points,

Thus, the second-derivative signal can be easily calculated from the spline fit. if desired, smoothing splines can be found to make the second-derivative less sensitive to random-errors.

The savvy reader will have already noticed that the data samples are related to the knot coefficients via a convolution operator, so that simple convolution with the sampled B-spline function recovers the original data from the spline coefficients. The output of convolutions can change depending on how boundaries are handled (this becomes increasingly more important as the number of dimensions in the data- set increases). The algorithms relating to B-splines in the signal- processing sub package assume mirror-symmetric boundary conditions. Thus, spline coefficients are computed based on that assumption, and data-samples can be recovered exactly from the spline coefficients by assuming them to be mirror-symmetric also.

Currently the package provides functions for determining second- and
third-order cubic spline coefficients from equally spaced samples in
one- and two-dimensions (`signal.qspline1d`,
`signal.qspline2d`, `signal.cspline1d`,
`signal.cspline2d`). The package also supplies a function (
`signal.bspline` ) for evaluating the bspline basis function,
for arbitrary order and For
large , the B-spline basis function can be approximated well
by a zero-mean Gaussian function with standard-deviation equal to
:

A function to compute this Gaussian for arbitrary and
is also available ( `signal.gauss_spline` ). The
following code and Figure uses spline-filtering to compute an
edge-image (the second-derivative of a smoothed spline) of Lena’s face
which is an array returned by the command `lena`. The command
`signal.sepfir2d` was used to apply a separable two-dimensional
FIR filter with mirror- symmetric boundary conditions to the spline
coefficients. This function is ideally suited for reconstructing
samples from spline coefficients and is faster than
`signal.convolve2d` which convolves arbitrary two-dimensional
filters and allows for choosing mirror-symmetric boundary conditions.

```
>>> from numpy import *
>>> from scipy import signal, misc
>>> import matplotlib.pyplot as plt
```

```
>>> image = misc.lena().astype(float32)
>>> derfilt = array([1.0,-2,1.0],float32)
>>> ck = signal.cspline2d(image,8.0)
>>> deriv = signal.sepfir2d(ck, derfilt, [1]) + \
>>> signal.sepfir2d(ck, [1], derfilt)
```

Alternatively we could have done:

```
laplacian = array([[0,1,0],[1,-4,1],[0,1,0]],float32)
deriv2 = signal.convolve2d(ck,laplacian,mode='same',boundary='symm')
```

```
>>> plt.figure()
>>> plt.imshow(image)
>>> plt.gray()
>>> plt.title('Original image')
>>> plt.show()
```

```
>>> plt.figure()
>>> plt.imshow(deriv)
>>> plt.gray()
>>> plt.title('Output of spline edge filter')
>>> plt.show()
```

Filtering is a generic name for any system that modifies an input signal in some way. In SciPy a signal can be thought of as a Numpy array. There are different kinds of filters for different kinds of operations. There are two broad kinds of filtering operations: linear and non-linear. Linear filters can always be reduced to multiplication of the flattened Numpy array by an appropriate matrix resulting in another flattened Numpy array. Of course, this is not usually the best way to compute the filter as the matrices and vectors involved may be huge. For example filtering a image with this method would require multiplication of a matrix with a vector. Just trying to store the matrix using a standard Numpy array would require elements. At 4 bytes per element this would require of memory. In most applications most of the elements of this matrix are zero and a different method for computing the output of the filter is employed.

Many linear filters also have the property of shift-invariance. This means that the filtering operation is the same at different locations in the signal and it implies that the filtering matrix can be constructed from knowledge of one row (or column) of the matrix alone. In this case, the matrix multiplication can be accomplished using Fourier transforms.

Let define a one-dimensional signal indexed by the integer Full convolution of two one-dimensional signals can be expressed as

This equation can only be implemented directly if we limit the sequences to finite support sequences that can be stored in a computer, choose to be the starting point of both sequences, let be that value for which for all and be that value for which for all , then the discrete convolution expression is

For convenience assume Then, more explicitly the output of this operation is

Thus, the full discrete convolution of two finite sequences of lengths and respectively results in a finite sequence of length

One dimensional convolution is implemented in SciPy with the function
`signal.convolve` . This function takes as inputs the signals
, and an optional flag and returns the signal
The optional flag allows for specification of which part of
the output signal to return. The default value of ‘full’ returns the
entire signal. If the flag has a value of ‘same’ then only the middle
values are returned starting at so that the output has the same
length as the largest input. If the flag has a value of ‘valid’ then
only the middle
output values are returned where depends on all of the
values of the smallest input from to
In other words only the values
to inclusive are
returned.

This same function `signal.convolve` can actually take
-dimensional arrays as inputs and will return the
-dimensional convolution of the two arrays. The same input flags are
available for that case as well.

Correlation is very similar to convolution except for the minus sign becomes a plus sign. Thus

is the (cross) correlation of the signals and For finite-length signals with outside of the range and outside of the range the summation can simplify to

Assuming again that this is

The SciPy function `signal.correlate` implements this
operation. Equivalent flags are available for this operation to return
the full length sequence (‘full’) or a sequence with the
same size as the largest sequence starting at
(‘same’) or a sequence where the values depend on all the values of
the smallest sequence (‘valid’). This final option returns the
values to
inclusive.

The function `signal.correlate` can also take arbitrary
-dimensional arrays as input and return the -dimensional
convolution of the two arrays on output.

When `signal.correlate` and/or
`signal.convolve` can be used to construct arbitrary image
filters to perform actions such as blurring, enhancing, and
edge-detection for an image.

Convolution is mainly used for filtering when one of the signals is much smaller than the other ( ), otherwise linear filtering is more easily accomplished in the frequency domain (see Fourier Transforms).

A general class of linear one-dimensional filters (that includes convolution filters) are filters described by the difference equation

where is the input sequence and is the output sequence. If we assume initial rest so that for , then this kind of filter can be implemented using convolution. However, the convolution filter sequence could be infinite if for In addition, this general class of linear filter allows initial conditions to be placed on for resulting in a filter that cannot be expressed using convolution.

The difference equation filter can be thought of as finding recursively in terms of it’s previous values

Often is chosen for normalization. The implementation in SciPy of this general difference equation filter is a little more complicated then would be implied by the previous equation. It is implemented so that only one signal needs to be delayed. The actual implementation equations are (assuming ).

where Note that if and if In this way, the output at time depends only on the input at time and the value of at the previous time. This can always be calculated as long as the values are computed and stored at each time step.

The difference-equation filter is called using the command
`signal.lfilter` in SciPy. This command takes as inputs the
vector the vector, a signal and
returns the vector (the same length as ) computed
using the equation given above. If is
-dimensional, then the filter is computed along the axis provided. If,
desired, initial conditions providing the values of
to can be
provided or else it will be assumed that they are all zero. If initial
conditions are provided, then the final conditions on the intermediate
variables are also returned. These could be used, for example, to
restart the calculation in the same state.

Sometimes it is more convenient to express the initial conditions in terms of the signals and In other words, perhaps you have the values of to and the values of to and would like to determine what values of should be delivered as initial conditions to the difference-equation filter. It is not difficult to show that for

Using this formula we can find the intial condition vector to given initial conditions on (and ). The command `signal.lfiltic` performs this function.

The signal processing package provides many more filters as well.

A median filter is commonly applied when noise is markedly non-
Gaussian or when it is desired to preserve edges. The median filter
works by sorting all of the array pixel values in a rectangular region
surrounding the point of interest. The sample median of this list of
neighborhood pixel values is used as the value for the output array.
The sample median is the middle array value in a sorted list of
neighborhood values. If there are an even number of elements in the
neighborhood, then the average of the middle two values is used as the
median. A general purpose median filter that works on N-dimensional
arrays is `signal.medfilt` . A specialized version that works
only for two-dimensional arrays is available as
`signal.medfilt2d` .

A median filter is a specific example of a more general class of
filters called order filters. To compute the output at a particular
pixel, all order filters use the array values in a region surrounding
that pixel. These array values are sorted and then one of them is
selected as the output value. For the median filter, the sample median
of the list of array values is used as the output. A general order
filter allows the user to select which of the sorted values will be
used as the output. So, for example one could choose to pick the
maximum in the list or the minimum. The order filter takes an
additional argument besides the input array and the region mask that
specifies which of the elements in the sorted list of neighbor array
values should be used as the output. The command to perform an order
filter is `signal.order_filter` .

The Wiener filter is a simple deblurring filter for denoising images. This is not the Wiener filter commonly described in image reconstruction problems but instead it is a simple, local-mean filter. Let be the input signal, then the output is

Where is the local estimate of the mean and is the local estimate of the variance. The window for these estimates is an optional input parameter (default is ). The parameter is a threshold noise parameter. If is not given then it is estimated as the average of the local variances.

The Hilbert transform constructs the complex-valued analytic signal from a real signal. For example if then would return (except near the edges) In the frequency domain, the hilbert transform performs

where is 2 for positive frequencies, for negative frequencies and for zero-frequencies.